Question
Does anyone out there own a bandsaw with a 36" or wider throat? I am looking to saw through logs to make table tops. I'm considering making or having made a bandsaw with 48"-60" throat. This is not for high speed/production but the quality of cut is important, any thoughts on using 1 1/2" blades with a cut this wide? I would also consider hiring someone to do this work, but I also don't want to use a chainsaw mill due to kerf loss. Any thoughts are appreciated.
Forum Responses
(Sawing and Drying Forum)
From contributor G:
Most mill makers are building portable mills. The wide throat mill would be over-width. My mill is 30" and at the limit for trailer width. I suppose you could get an over sized load permit. I am sure Mighty Mite would make you a special mill that would be bigger, they could come up with a rotating saw for trailering. Likely the Gen III would be the one to modify.
Have you considered using a large chain saw and then machining the pieces (perhaps using a floor sander) to the required thickness? Sawing is indeed a difficult situation for you, but I suspect that drying will be even more difficult. A cut near the center of a log will certainly cup, especially with a 36" diameter log.
Be warned what has been stated is true. The blade will cup inside the cut, it is very slow, and it does take a lot of HP to pull the blade through the cut. You'll need to wedge the slab as you cut. If you have a band break in the cut, good luck getting it out. Also loading big logs is hairy even with a mill built out of 4x8 3/8 tubing.
You should be able to build a chainsaw slabber for under a couple grand if you use a small i/c engine instead of saw heads. You should be able to find harvester hubs and sprockets that would fit a 20+hp Briggs or Kohler. Or you can drive the chain via a jack shaft set up.
We could haul the chainsaw and jig to the tree, verses the other way around - which is a big deal with large trees, and the coin factor. It cost us very little to make those wide boards versus trying it with a specialty band mill. The handling and drying were by far more of an issue than how to do the cut for us though. That being said I am much happier behind the control head on the Woodmizer 40 Super, buzzing through the normal sized logs, spitting out great lumber day in and day out than dealing with the hog logs.
Comment from contributor H:
I built a portable bandsaw that cuts up to 60". It is electric over hydraulic and I run 2” and 3” 042 blades. The key is to have the blade perfectly level to the deck. It cuts perfect, but it did cost about 20k to build and was completed in three months. Keep the tooth speed under 5,000 and buy sturdy guides.
Common Lumber Name | A | B | C |
Hardwoods | |||
Alder, Red | 9.9 | 19.2 | 2506 |
Apple | 10.9 | 31.7 | 4132 |
Ash, Black | 9.3 | 23.4 | 4132 |
Ash, Green | 14.3 | 27.6 | 3590 |
Aspen, Bigtooth | 10.3 | 18.7 | 2439 |
Aspen, Quaking | 10.3 | 18.2 | 2373 |
Basswood | 6.2 | 16.6 | 2174 |
Beech, American | 8.9 | 29.1 | 3793 |
Birch, Paper | 8.8 | 25.0 | 3260 |
Birch, Sweet | 11.9 | 31.2 | 4065 |
Birch, Yellow | 9.2 | 28.6 | 3723 |
Buckeye | 8.9 | 17.2 | 2235 |
Butternut | 11.3 | 18.7 | 2440 |
Cherry | 13.8 | 24.4 | 3184 |
Chesnut, American | 11.6 | 20.8 | 2708 |
Cottonwood | 8.5 | 16.1 | 2102 |
Dogwood | 6.8 | 33.3 | 4331 |
Elm, American | 10.2 | 23.9 | 3116 |
Elm, Rock | 12.2 | 29.6 | 3860 |
Elm, slippery | 11.5 | 25.0 | 3251 |
Hackberry | 11.8 | 25.5 | 3319 |
Hickory, Bitternut (Pecan) | 14.7 | 31.2 | 4062 |
Hickory (True) | |||
Hickory, Mockernut | 9.1 | 33.3 | 4332 |
Hickory, Pignut | 9.3 | 34.3 | 4332 |
Hickory, Shagbark | 10.9 | 33.3 | 4333 |
Hickory, Shellbark | 6.6 | 32.2 | 4195 |
Holly, American | 8.3 | 26.0 | 3387 |
Hophornbeam, Eastern | 7.9 | 32.8 | 4266 |
Laurel, California | 15.1 | 26.5 | 3456 |
Locust, Black | 21.2 | 34.3 | 4470 |
Madrone, Pacific | 7.8 | 30.2 | 3925 |
Maple (Soft) | |||
Maple, Bigleaf | 12.8 | 22.9 | 2980 |
Maple, Red | 13.1 | 25.5 | 3318 |
Maple, Silver | 12.4 | 22.9 | 2981 |
Maple (Hard) | |||
Maple, Black | 12.3 | 27.0 | 3523 |
Maple, Sugar | 12.3 | 29.1 | 3793 |
Oak (Red) | |||
Oak, Black | 11.7 | 29.1 | 3792 |
Oak, California black | 16.4 | 26.5 | 3455 |
Oak, Laurel | 6.3 | 29.1 | 3791 |
Oak, Northern red | 13.6 | 29.1 | 3793 |
Oak, Pin | 13.0 | 30.2 | 3928 |
Oak, Scarlet | 13.2 | 31.2 | 4065 |
Oak, Southern red | 9.6 | 27.0 | 3520 |
Oak, Water | 10.4 | 29.1 | 3793 |
Oak, Willow | 6.4 | 29.1 | 3790 |
Oak (White) | |||
Oak, Bur | 15.4 | 30.2 | 3928 |
Oak, Chestnut | 10.1 | 29.6 | 3858 |
Oak, Live | 17.5 | 41.6 | 5417 |
Oak, Overcup | 10.7 | 29.6 | 3860 |
Oak, Post | 11.0 | 31.2 | 4063 |
Oak, Swamp chestnut | 10.7 | 31.2 | 4063 |
Oak, White | 10.8 | 31.2 | 4062 |
Persimmon | 7.0 | 33.3 | 4332 |
Sweetgum | 8.9 | 23.9 | 3115 |
Sycamore | 10.7 | 23.9 | 3115 |
Tanoak | 9.0 | 30.2 | 3926 |
Tupelo, Black | 10.4 | 23.9 | 3116 |
Tupelo, Water | 12.4 | 23.9 | 3115 |
Walnut | 13.4 | 26.5 | 3454 |
Willow, Black | 8.6 | 18.7 | 2438 |
Yellow-poplar | 10.6 | 20.8 | 2708 |
Common Lumber Name | A | B | C |
Softwoods | |||
Baldcypress | 13.2 | 21.9 | 2844 |
Cedar, Alaska | 14.4 | 21.9 | 2844 |
Cedar, Atlantic white | 10.9 | 16.1 | 2100 |
Cedar, eastern red | 16.4 | 22.9 | 2981 |
Cedar, Incense | 13.1 | 18.2 | 2371 |
Cedar, Northern white | 11.1 | 15.1 | 1964 |
Cedar, Port-Orford | 12.6 | 20.2 | 2641 |
Cedar, Western red | 12.2 | 16.1 | 2100 |
Douglas-fir, Coast type | 12.3 | 23.4 | 3049 |
Douglas-fir, Interior west | 13.2 | 23.9 | 3116 |
Douglas-fir, Interior north | 14.0 | 23.4 | 3048 |
Fir, Balsam | 9.9 | 17.2 | 2236 |
Fir, California red | 10.6 | 18.7 | 2437 |
Fir, Grand | 10.7 | 18.2 | 2371 |
Fir, Noble | 10.1 | 19.2 | 2507 |
Fir, Pacific silver | 10.4 | 20.8 | 2711 |
Fir, Subalpine | 10.5 | 16.1 | 2101 |
Fir, White | 12.2 | 19.2 | 2506 |
Hemlock, Eastern | 12.6 | 19.8 | 2573 |
Hemlock, Western | 11.5 | 21.8 | 2847 |
Larch, Western | 11.3 | 25.0 | 3251 |
Pine, Eastern white | 12.3 | 17.7 | 2303 |
Pine, Lodgepole | 11.5 | 19.8 | 2576 |
Pine, Ponderosa | 12.6 | 19.8 | 2573 |
Pine, Red | 12.2 | 21.3 | 2777 |
Southern yellow group | |||
Pine, Loblolly | 12.9 | 24.4 | 3183 |
Pine, Longleaf | 15.0 | 28.1 | 3658 |
Pine, Shortleaf | 12.9 | 24.4 | 3183 |
Pine, Sugar | 12.6 | 17.7 | 2302 |
Pine, Western white | 10.0 | 18.2 | 2370 |
Redwood, Old growth | 14.9 | 19.8 | 2573 |
Redwood, Second growth | 13.2 | 17.7 | 2302 |
Spruce, Black | 11.3 | 19.8 | 2575 |
Spruce, Engelmann | 10.0 | 17.2 | 2234 |
Spruce, Red | 10.6 | 19.2 | 2506 |
Spruce, Sitka | 10.8 | 19.2 | 2506 |
Tamarack | 12.0 | 25.5 | 3318 |