Knife Grinding and Woodworking Manual 5 -- Excerpts Part 5
One in a series of excerpts from the grinding manual of Charles G.G. Schmidt & Company. 1998.

Knife Grinding and Woodworking Manual 6 -- Excerpts Part 6
One in a series of excerpts from the grinding manual of Charles G.G. Schmidt & Company. 1998.

Knife Grinding and Woodworking Manual 1 -- Excerpts Part 1
One in a series of excerpts from the grinding manual of Charles G.G. Schmidt & Company. 1998.

Knife Grinding and Woodworking Manual 2 -- Excerpts Part 2
One in a series of excerpts from the grinding manual of Charles G.G. Schmidt & Company. 1998.

Capacitor ratings and installation
Technical information on the installation of capacitors. Rule one: Call an electrician. November 29, 2000

Knife Grinding and Woodworking Manual 4 -- Excerpts Part 4
One in a series of excerpts from the grinding manual of Charles G.G. Schmidt & Company. 1998.

Choosing a moulder
Jointed- vs. non-jointed-head moulders; choosing the right machine for a custom moulding business. November 21, 2000

Sharpening Hand Tools with Sandpaper
Chisels and planes take a keen edge using increasing grits of sandpaper glued to glass. Here, pros discuss the fine points of achieving that wicked edge. December 15, 2005


Maintaining Sharpening and Honing Stones
Solid advice on selecting and using water stones and oil stones, and about how to keep them clean and flat. November 16, 2010

Knife Grinding and Woodworking Manual 3 -- Excerpts Part 3
One in a series of excerpts from the grinding manual of Charles G.G. Schmidt & Company. 1998.

Three-phase electricity primer
Pros and cons of three-phase electricity and static and rotary phase converters. November 21, 2000

Tools to choose in setting up shop
Selecting the best makes and models of tools when starting out. October 31, 2000

Correcting dowel hole runout
Finding and correcting the cause of dowel hole runout in CNC-machined parts. November 7, 2000

Chisel Sharpening Setups
Woodworkers discuss jigs and equipment for sharpening chisels. May 13, 2009

Cleaning and Lubricating Router Bits
people sometimes reach for the wrong stuff when trying to loosen up a bearing. August 14, 2007

Routing phenolic paper
A discussion of the best bits and techniques for cutting phenolic paper on a CNC router. November 15, 2000

Keeping track of blade sharpenings
Comparing notes on noting the service history of sawmill blades. July 4, 2000

Jointing knives of a side-head planer
Choosing and using the proper stone when jointing knives used in a side-head planer. November 7, 2000

Cleaning the Kremlin Airmix system
Solvent recycling methods and hose products to help decrease the cost of cleaning and maintaining the Kremlin Airmix system. November 21, 2000

Sawing square timbers
Producing square timbers on the sawmill. November 15, 2000

Cutting creosoted poles
Advice on cutting (or not cutting) utility poles treated with creosote. June 20, 2000

Preventing kickback
Diagosing the causes of recurring kickback, and finding cures. 1998.

Verifying moisture meters' accuracy
A discussion of ways to verify the accuracy of moisture meters. Includes info on calibration. June 21, 2000

Sawdust buildup in discharge chute
How to remedy pine-tar buildup leading to clogged discharge chutes during sawing. July 26, 2000

Hand-Sharpening Plane Irons
Woodworkers discuss how to sharpen and "round" a smoothing plane iron. October 28, 2005

Chisels for Hand-Cut Dovetails
Woodworkers talk about chisel quality, sharpening, and dovetail joinery. October 28, 2005

Sharpening Files
You can send files out to be re-sharpened. Lore also says you can sharpen them up yourself by soaking them in battery acid or vinegar. October 28, 2005

Honing Your Way to the Perfect Edge
An extensive discussion on chisel and plane iron sharpening walks through the basic and advanced aspects of creating a shaving-sharp edge on your hand tools. May 13, 2013

Tape-Measure Accuracy
Like everything else in life, tape measures are imperfect. But here are a couple of suggestions for improving accuracy. October 11, 2007

The Ten-Cent Router Switch Repair
A woodworker fixes the variable-speed control dial on his DeWalt plunge router by sliding a dime under it. Go figure.January 3, 2012

Construire un convertisseur de phase rotatif
Comment construire un convertisseur de phase rotatif. 29 novembre 2000

Building a rotary phase converter
How to build a rotary phase converter. November 29, 2000

Cleaning glue out of edgebander
The tedious process, illustrated. October 30, 2003

CNC tooling: What's the best?
Solving the problems of worn-out router bits and torn-out melamine. January 3, 2001

Too-tight biscuits
Biscuit joining tricks and techniques. March 23, 2002

Touching Up the Burnt Ends of a Routed Flute
Here's advice on cleaning up the rounded end of a flute if the router leaves burn marks — and on scraper sharpening, and on how to avoid those burn marks to begin with. February 11, 2010

Router Table and Lift
Designs and ideas for a smoothly functioning router workstation. December 9, 2004

Clamp Cart
Shop-made carriers for clamps. December 26, 2004

Reviving an Old Sharpening Stone
Here's the story of an old, legacy grinding wheel and the difficulties a woodworker encountered while trying to make it work again. January 2, 2012

Setting up a powerfeeder
The care and use of powerfeeders. November 7, 2000

Sharpening Equipment
A basic description of tool sharpening equipment and its use. November 13, 2008

Sliding table saw basics
General information for first-time users of 'sliders.' 1998.

3-phase to single phase
Is it possible to convert 3-phase equipment to single-phase power? March 20, 2001

An Ax to Grind - A Practical Ax Manual
History, maintenance tips, and how-to for that ancient woodworking tool, the axe. December 21, 2009

Getting Your Waterstone Back in Shape
If your waterstone isn’t flat, it can’t deliver a proper edge to your tools. Here's how to fix that. December 18, 2013

How to Smooth and Flatten a Tablesaw Table
A palm sander will do a decent job of removing scratches, but you can also have the thing professionally ground flat. April 27, 2007

Calibrating a Hollow Chisel Mortiser
Careful adjustments to the spacing between the chisels and the bit can prevent overheating, smoking, and chisel breakage. January 3, 2012

Today's Sponsors
  • Forestry.com
    Forestry.com is a specialized platform with educational content and equipment for Loggers and Foresters
  • Colonial Saw
    North American Supplier of Striebig Panel Saws, Lamello Specialty Tools and a Wide Range of Saw and Tool Grinding Machinery
  • iBiDMachinery
    The Nation's #1 Used Woodworking Marketplace - Buy and Sell Woodworking Equipment with iBiD!
  • Simantech
    New & Used Machinery, Supplies, Tooling, Parts, and Abrasive Products
  • The Millwork Studio
    Millwork Shop Drawings and Estimates
  • Centex Automation
    New and Used Machinery sales and service
  • Western Dovetail
    Custom Made Dovetail Drawers
  • American Vision Cabinets
    Leading provider of Custom CNC cabinet parts and components and Edge banding services
  • TotalFinishingSUPPLIES.com
    Solutions and supplies from spray tips to spray booths for all your woodworking needs
  • VortexTool Co. Inc.
    Manufacturers of Custom Cutting Tools, and Distributors of Major Cutting Tool Brands
  • Limtech Industries, Inc.
    CNC Routers, Machinery for Woodworking, Plastic and Other Non-ferrous Metal Machining Applications
  • Parts Cutter CNC
    CNC Cabinetry and Closet Parts
  • Template Services
    Professional Moulding Design and Template Making Service

Become a Sponsor today!